Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionLast revisionBoth sides next revision | ||
projects:howtos:openwrt-repeater [2015/07/09 02:36] – created prometheus | projects:howtos:openwrt-repeater [2015/07/09 03:02] – [Walktrhough] prometheus | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== openWRT (Wireless) Repeater ====== | ====== openWRT (Wireless) Repeater ====== | ||
+ | |||
+ | ===== Walktrhough ===== | ||
+ | |||
+ | - Network | ||
+ | - Interfaces | ||
+ | - LAN | ||
+ | - Generel Setup --> Alter the third byte to a number that is **non-identical** with the one of your host network you will connect to. (i.e.: FritzBox gives you 192.168.178.XXX, | ||
+ | - Save & Apply | ||
+ | |||
+ | - Network | ||
+ | - Wifi | ||
+ | - ' | ||
+ | - Choose your network and hit the 'Join network' | ||
+ | - Enter all needed security parameters. Select the wan option. | ||
+ | - Save & Apply | ||
+ | - Underneath ' | ||
+ | - Under ' | ||
+ | - Save & Apply | ||
+ | - Under ' | ||
+ | - Save & Apply | ||
+ | |||
+ | Connect to your openWRT AP with a network cable and surf the Internet. To know how to extend this to a wireless repeater, read on. | ||
+ | |||
+ | - Network | ||
+ | - Wifi | ||
+ | - Underneath ' | ||
+ | - Under ' | ||
+ | - On the ' | ||
+ | - (Optionally you can still configure some security parameters in the ' | ||
+ | - Save & Apply | ||
+ | |||
+ | Hit the roads of the Internet. If you encounter any troubles, read the Troubleshooting section or compare theconfigs. | ||
+ | |||
+ | ===== configs ===== | ||
+ | |||
**/ | **/ | ||
Line 105: | Line 140: | ||
**/ | **/ | ||
- | </code> | + | < |
config ' | config ' | ||
Line 195: | Line 230: | ||
</ | </ | ||
- | ===== Troubleshooting ===== | + | **/ |
- | - What if openWRT constantly disconnects from the host access point? | + | < |
- | + | config network | |
- | This might be related to the fact, that your access points uses the same ESSID on the 2.4GHz as 5GHz channel. The fix is either to disable one of them on your host AP, reconnect 'til it works or check for another openWRT version for your device. | + | |
- | + | list affects dhcp | |
- | It might also be that the openWRT | + | list affects radvd |
- | + | ||
- | - The ' | + | config |
+ | list affects network | ||
+ | |||
+ | config firewall | ||
+ | option init firewall | ||
+ | list affects luci-splash | ||
+ | list affects qos | ||
+ | list affects miniupnpd | ||
+ | |||
+ | config olsr | ||
+ | option init olsrd | ||
+ | |||
+ | config dhcp | ||
+ | option init dnsmasq | ||
+ | |||
+ | config dropbear | ||
+ | option init dropbear | ||
+ | |||
+ | config httpd | ||
+ | option init httpd | ||
+ | |||
+ | config fstab | ||
+ | option init fstab | ||
+ | |||
+ | config qos | ||
+ | option init qos | ||
+ | |||
+ | config system | ||
+ | option init led | ||
+ | list affects luci_statistics | ||
+ | |||
+ | config luci_splash | ||
+ | option init luci_splash | ||
+ | |||
+ | config upnpd | ||
+ | option init miniupnpd | ||
+ | |||
+ | config ntpclient | ||
+ | option init ntpclient | ||
+ | |||
+ | config samba | ||
+ | option init samba | ||
+ | |||
+ | config tinyproxy | ||
+ | option init tinyproxy | ||
+ | </ | ||
+ | ===== Troubleshooting ===== | ||
- | Looks like a bug in the openWRT GUI. Ignore it an verify it via ssh on the access point. | + | - **What if openWRT constantly disconnects from the host access point?** \\ \\ This might be related to the fact, that your access points uses the same ESSID on the 2.4GHz as 5GHz channel. The fix is either to disable one of them on your host AP, reconnect 'til it works or check for another openWRT version for your device. \\ \\ It might also be that the openWRT wireless host is not on the same channel as the host AP. \\ \\ |
+ | - **The ' | ||