Differences

This shows you the differences between two versions of the page.

--- private:freifunk:bugs [2019/09/11 22:19] – fantawams
+++ private:projects:freifunk:bugs [2021/10/17 21:51] – fantawams
@@ Line 3: / Line 3: @@
 ==== Firmware ====
-=== stable ===
-^Firmware version^Bug^Solution^
-| 2.0.3 | knows only old GW1 | update to new Version |
-| 2.0.5 | knows only old GW1 | update to new Version |
-| 2.1.0 | does not know new GW3 | update to new Version |
-| 2.1.0 | auto-update bug, nodes stuck in boot loop on firmware update | POWER OFF/POWER ON node. Update to new Version. If update is not possible, re-flashing the node needs to be done. |
-| 2.1.1 | does not know new GW3 | update to new Version |
-| 2.1.1 | auto-update bug, nodes stuck in boot loop on firmware update | POWER OFF/POWER ON node. Update to new Version. If update is not possible, re-flashing the node needs to be done. |
-=== experimental ===
 <note important>Keep in mind,that installing an experimental firmware on a router may brick the device. It should only be installed to test new firmware and new hardware.</note>
-^Firmware version^Bug^work-around^
+^ Firmware version  ^ Bug                                                           ^ Solution                                                                                                                    ^
-| 2.2.0~exp20181221 | NO LAN IPV4 | / |
+| 2.0.3             | knows only old GW1                                            | update to at least Version 2.3                                                                                              |
+| 2.0.5             | knows only old GW1                                            | update to at least Version 2.3                                                                                              |
+| 2.1.0             | does not know new GW3                                         | update to at least Version 2.3                                                                                              |
+| 2.1.0             | auto-update bug, nodes stuck in boot loop on firmware update  | POWER OFF/POWER ON node. Update to at least Version 2.3. If update is not possible, re-flashing the node needs to be done.  |
+| 2.1.1             | does not know new GW3                                         | update to new Version                                                                                                       |
+| 2.1.1             | auto-update bug, nodes stuck in boot loop on firmware update  | POWER OFF/POWER ON node. Update to at least Version 2.3. If update is not possible, re-flashing the node needs to be done.  |
+| 2.2.0~exp20181221 | NO LAN IPV4, comes from network | / |
 | 2.2.0~exp20181221 | No config mode webgui after firmware update | re-flashing the node |
-| 2.2.0~exp20190328 | NO LAN IPV4 | / |
+| 2.2.0~exp20190328 | NO LAN IPV4, comes from network | / |
 | 2.2.0~exp20190328 | No config mode webgui after firmware update | re-flashing the node |
-| 2.2.0~exp20190717 | NO LAN IPV4, may come from network | / |
+| 2.2.0~exp20190717 | NO LAN IPV4, comes from network | / |
+| 2.2.0~exp20190909 | NO LAN IPV4, comes from network. contact info is not mandatory | /|
+| < 2020.X | does not know new GW2 | update the node to at least Gluon 2020.x |
+| < 2020.2.3 | does not know new GW1 | update the noew at least Gluon 2020.2.3 |
 ==== network ====
 ^Bug^reason^solution^work-around^
-| IP distribution on nodes, some times no IPV4 some time IPV4 and IPV6, no differnence if node is connected to GW2 or GW3 | / | / | reboot the node |
+| IP distribution on nodes, some times no IPV4 some time IPV4 and IPV6, no differnence if node is connected to GW2 or GW3 | / | solved | reboot the node |
+| Failover not working from GW2 to GW3 | / | reason found, under monitoring |